The store will re-open on .
Click on a product name below view support resources and technical specifications about that product.
128.323 KB
Thread Female: 1.0″
Height: 5.0″
Diameter: 3.75″
Operating Pressure: 4 – 100 psi
Optimal Operating Pressure: 8 – 100 psi
Flow Rate: Approx. 80% of flow supplied to valve
Max Fluid Temp: 175° F
The Hudson Valve should be routinely cleaned to maintain optimal performance. Depending on your water source, cleaning should take place between 2 – 6 times per year. The more silt, rust, debris, etc. in your water, the more often you need to clean the valve. Moss, algae and other debris can clog the small holes that run through the valve causing it to stop working properly. Follow these steps for optimal performance.
10.076 MB
10.063 MB
319.077 KB
565.256 KB
849.575 KB
625.79 KB
1.364 MB
200.629 KB
915.213 KB
1.718 MB
3.557 MB
1.208 MB
1.046 MB
8‑mil
25-mil
17.5 psi
41.0 psi
0.638 in
0.636 in
12 inches
0.23 gallons per hour at 10.0 psi
0.42 gallons per hour at 10.0 psi
3.557 MB
1.909 MB
172.408 KB
1.677 MB
1.73 MB
1.677 MB
3.557 MB
Screen or disc filters
Manual or automatic valve with 35 psi pressure regulator
4.9 gpm
9.8 gpm
3⁄4″ diameter or greater supply line works best
1″ diameter or greater supply line works best
At least 30 psi
Pivot Response™
Innovative Pivot Response Technology makes sharpening easier and more precise by allowing the abrasive to follow the curve of the blade when sharpening. It creates a sharp and consistent edge along the entire length of the blade. Pivot Response Technology is available in two ways: Convex Carbides and Bench Stones.
Convex Carbide™
Work Sharp’s exclusive Convex Carbide sharpening system creates a superior convex edge profile quickly and easily. Convex edges cut smoother and hold their edge longer. Our Convex Carbides also provide the innovative Pivot Response Technology. This allows the carbides to follow the curve of the blade when sharpening and provides increased control of material take off to restore a sharp edge quickly. Pivot Response can be locked out to provide less material take off for quickly restoring a lightly dulled edge. Work Sharp’s innovative technologies allow you to take more control of the sharpening results you want, without adding complexity. Our engineered simplicity puts the skill into the tool, so you get sharper edges faster.
25°
4.731 MB
4.658 MB
5 Burners
Upgradable to 8 Burner
8 Burners
2 inches
90°+ adjustment
50° adjustment
35° adjustment
Adjustable to either 6 ¾” or 10 ¾”
Swap and invert axle assemblies to increase cart height
Expandable from 31″ – 38″ inside wheel width
Expandable from 42″ – 54″ inside wheel width
300,000 BTUs at 25 psi
480,000 BTUs at 25 psi
308.244 KB
1.73 MB
Cordless drill (not included)
15″ wide
20″ × 26″ × 6″
10 pounds
Cutting the silage tarp will not fray the edges or compromise the integrity. Learn more.
Width: 9 inches
Height: 9 inches
Length: 46 inches
Weight: 61 lbs
Width: 9 inches
Height: 9 inches
Length: 60 inches
Weight: 83 lbs
Width: 9 inches
Height: 9 inches
Length: 70 inches
Weight: 99 lbs
Width: 9 inches
Height: 9 inches
Length: 86 inches
Weight: 124 lbs
100% Low Density Polyethylene (LDPE). It does not contain Polyvinyl Chloride (PVC).
365 sunny days on both sides. Learn more.
Both sides. Learn more.
5 mil
710.406 KB
566.232 KB
172.408 KB